Supermicro SUPERSERVER 6013A-T Скачать руководство пользователя страница 78

Страница: 78 / 126

7-10

UPER

ERVER 6013A-T User's Manual

PCI/PnP Configuration

Plug & Play O/S

Select "Yes" to allow the operating system to configure Plug & Play devices

that are not required when booting up the system, if Plug & Play is sup-

ported by the OS. Select "

" to allow the BIOS to configure Plug & Play

devices when the system is booting up.

PCI Latency Timer

This option sets the latency of all PCI devices on the PCI bus. Select a

number listed to set the PCI latency to that many PCI clock cycles. The

settings are "32, "

", "96", "128", "160", "192", "224" and "248".

Allocate IRQ to PCI VGA

Set this value to allow or restrict the system from giving the VGA adapter

card an interrupt address. The options are "

Yes

" and "No".

Palette Snooping

Set this value to allow the system to modify the Palette Snooping settings.

This setting should not be changed unless the VGA card manufacturer

indicates otherwise. Select "Enabled" to inform the PCI devices that an ISA

based graphics device is installed in the system so that the card will func-

tion correctly. Always check with your adapter card’s manuals first before

modifying the default settings in the BIOS. The options are "Enabled" and

Disabled

PCI IDE BusMaster

Set this value to allow or prevent the use of PCI IDE busmastering. Select

"Enabled" to allow the BIOS to use PCI busmaster for reading and writing to

IDE drives. The options are "

Disabled

" and "Enabled".

OffBoard PCI/ISA IDE Card

Set this value to allow the OffBoard PCI/ISA IDE Card to be selected. Select

Auto

" to allow the BIOS to automatically select the location of an OffBoard

PCI IDE adapter card. Select "PCI Slot1" only when there is an IDE adapter

card installed in PCI Slot 1. Select "PCI Slot2" only when there is an IDE

adapter card installed in PCI Slot 2. Select "PCI Slot 3" only when there is an

IDE adapter card installed in PCI Slot 3. Select "PCI Slot 4" only if there is an

IDE adapter card installed in PCI Slot 4.

Содержание SUPERSERVER 6013A-T































































































































Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6013A-T, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6013A-T

Отзывы:

Бренды по названию

Популярные бренды