SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 70

Страница: 70 / 74

Page | 70

Hybrid Inverter | Installer Manual

6.2. Information for Commissioning the Inverter

After you have successfully powered up the inverter, it must be programmed and set up as per
the programming feature above.

Check each bond on
the solar panels

Check the VOC does
not exceed 480V

Ensure both MPPTs
are balanced

Measure the sup-
ply voltage check it
matches the settings
of the inverter

If it falls out of the set-
ting range it will cause
the inverse shut down
and alarm

See Grid Setup page

Check the battery
charge and discharge
is within the C rating
of the battery. Too
high will damage the
battery

Check the battery
BMS is communicat-
ing with the inverter

This is the heart of the
system this controller
everything

Ensure you are fa-
miliar with this, if you
fully understand the
controller you will fully
appreciate the capa-
bilities of this inverter

See section ‘Program
Charge / Discharge
Times’

This is for paralleling
systems (Under De-
velopment), and wind
turbine

If paralleling inverters
in 3 Phase check you
phase rotation before
switching on the AC
Load, in 3 Phase the
output voltage will in-
crease across phase
to 400V

If using a wind turbine
please ensure you
have the correct limit-
ing resistor, caps and
rectifier

Familiarize yourself
with common fault
codes

Содержание SUN-25K-SG01HP3-EU-BM2











































































Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды

SunSynk SUN-25K-SG01HP3-EU-BM2, Руководство по установке

Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды