SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 74

background image

Page | 21

Hybrid Inverter | Installer Manual

5. Appliances such as air conditioner are required at least 2-3 minutes to restart because it is

required to have enough time to balance refrigerant gas inside of circuit. If a power shortage
occurs and recovers in short time, it will cause damage to your connected appliances. To
prevent this kind of damage, please check manufacturer of air conditioner if it is equipped
with time-delay function before installation. Otherwise, this inverter will trigger overload fault
and cut off output to protect your appliance but sometimes it still causes internal damage
to the air conditioner

4.6. PV Connection

Before connecting to PV panels, install a separate DC circuit breaker between the inverter and
PV modules. In addition, we request users install PV junction box with surge protection to pro-
tect the system from lightning strike.
In order to reduce risk of injury, please use the recommended cable sizes as shown below:

Be sure that AC power source is disconnected before attempting to wire it to the
unit.

To avoid any malfunction, do not connect any PV modules with possible leakage
current to the inverter. For example, grounded PV modules will cause leakage cur-
rent to the inverter. When using PV modules, please ensure the PV+ & PV- of solar
panel is not connected to the system ground bar.

It is requested to use PV junction box with surge protection. Otherwise, it will cause
damage on inverter when lightning occurs on PV modules.

«
...
19
20
21
22
23
...
»

Содержание SUN-25K-SG01HP3-EU-BM2











































































Отзывы:

Нет отзывов

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренд: Patton electronics Страницы: 16

Бренд: Danfoss Страницы: 36

Бренд: Magnum Energy Страницы: 2

Бренд: Magnum Energy Страницы: 62

Бренд: CanadianSolar Страницы: 27

GUARDIAN SERIES

Бренд: Generac Power Systems Страницы: 12

Бренд: Northern Lights Страницы: 35

Бренд: La Marche Страницы: 32

BeoLink Converter NL/ML

Бренд: Bang & Olufsen Страницы: 45

MAXX SST VEC054D

Бренд: Vector Страницы: 44

Бренд: Davis Instruments Страницы: 24

Бренд: CyberPower Страницы: 1

Evershine TLC4000

Бренд: Zeversolar Страницы: 74

Бренд: Delta-Opti Страницы: 3

Бренд: Tripp Lite Страницы: 4

Бренд: Tektronix Страницы: 132

Бренд: KROHNE Страницы: 12

Бренд: TR-Electronic Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды