SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 74

background image

Page | 15

Hybrid Inverter | Installer Manual

4.3. Mounting the Inverter

ALSO CONSIDER:

Installing the indoor unit, outdoor unit, power supply cable, transmission cable, and remote
control cable at least 1 metre away from any television or radio receiver. This will prevent TV
reception interference or radio noise. This will prevent radio signal interference from external
units that might interfere with the Wi-Fi or GSM monitoring.

If children under 10 years old may approach the unit, take preventive measures so that they
cannot reach and touch the unit.

Install the indoor unit on the wall where the height from the floors is higher than 1600mm.

Before connecting all wires, please take the metal cover off removing the screws as shown
below:

Select installation locations that adequate to support the weight of the converter.

Install this inverter at eye-level to allow the LCD to be read anytime.

An appropriate ambient temperature is between -25 ~ 60°C to ensure optimal operation.

Be sure to keep other objects and surfaces as shown in the figure to guarantee sufficient
heat dissipation and have enough space to remove wires.

For proper air circulation to dissipate heat, allow a clearance of approximately 50cm to the
side.

Risk of injury (Heavy Object)

Remember that this inverter is heavy (75kg) so users must be careful in handling
the unit during installation especially when mounting or removing from a wall.

«
...
13
14
15
16
17
...
»

Содержание SUN-25K-SG01HP3-EU-BM2











































































Отзывы:

Нет отзывов

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренд: K&S BASIC Страницы: 17

Бренд: Peachtree Audio Страницы: 56

Giga-McBasic-II

Бренд: B&B Electronics Страницы: 14

Бренд: VigilLink Страницы: 6

BN Products BNG8000iD

Бренд: Benner-Nawman Страницы: 28

Бренд: National Communications Страницы: 20

VideoExpress Converter

Бренд: Miglia Страницы: 12

EXT-DVIDL-2-HDMIR

Бренд: Gefen Страницы: 14

INVERTER PUMP CONTROL 5

Бренд: Profi-pumpe Страницы: 20

Go Power! SOLAR FLEX KIT GP-FLEX-100

Бренд: Valterra Products Страницы: 22

Бренд: wattsonic Страницы: 121

Бренд: roco Страницы: 24

Бренд: Black Box Страницы: 54

Бренд: SRS Lighting Страницы: 4

Бренд: SimpliPhi Страницы: 30

Бренд: Darfon Страницы: 8

Бренд: Televes Страницы: 16

Бренд: Trycom Technology Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды