SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 40

Страница: 40 / 74

Page | 40

Hybrid Inverter | Installer Manual

5.9. Factory Reset and Lock Code

To access the Settings, click on the gear icon on the right top of the navigation menu.

What you can do from this page:

Factory Reset:

Reset all parameters of the inverter

Lock out all changes:

Enable this menu to set parameters that before the unit is locked and

cannot be reset.

*Before performing a successful ‘Factory Reset’ and locking the systems the user
must enter a password to allow the setting to take place. The password for ‘Factory
Reset’ is 9999 and for lock out is 7777.

System self-check:

Allows the user to conduct a system diagnosis.

Test mode (only for engineers):

For engineers to conduct tests.

What this page displays:

Reset status.

Whether the ‘lock code’ is used or
not.

What you can do from this page:

Reset the inverter to the factory set-
tings.

System diagnostics.

Change or set the ‘lock code’.

Содержание SUN-25K-SG01HP3-EU-BM2











































































Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды

SunSynk SUN-25K-SG01HP3-EU-BM2, Руководство по установке

Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды