SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 38

Страница: 38 / 74

Page | 38

Hybrid Inverter | Installer Manual

5.6. Setup Page

To access the Settings, click on the gear icon on the right top of the navigation menu.

What this page displays:

Serial number.

Software version.

Time, Date, and MCU.

What you can do from this page:

Access the Basic Setup Page (press the BASIC icon).

Access the Battery Setup Page (press the BATTERY icon).

Access the Grid Setup Page (press the GRID icon).

Access the real-time programmable timer/system mode (press the SYSTEM MODE icon).

Access the advanced settings such as Wind Turbine (press the ADVANCE icon).

Access the auxiliary load/smart load settings (press the AUX LOAD icon)

Access the fault code register (press the FAULT CODES icon).

Set up Li BMS (press the LI BMS icon).

5.7. Set Time (Clock)

To set time, click on the BASIC icon and then on ‘Time’

What this page displays:

Time.

Date.

AM/PM.

What you can do from this page:

Adjust / set time.

Adjust / set date.

Adjust / set AM/PM.

How to set up (step-by-step):

1.  Touch the screen on the box you wish to change.
2.  Change the number (increase/decrease) using the UP and DOWN buttons.
3.  Press OK to set the changes

Содержание SUN-25K-SG01HP3-EU-BM2











































































Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды

SunSynk SUN-25K-SG01HP3-EU-BM2, Руководство по установке

Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды