SunSynk SUN-25K-SG01HP3-EU-BM2 Скачать руководство пользователя страница 62

Страница: 62 / 74

Page | 62

Hybrid Inverter | Installer Manual

Aux Load off Battery %

or Voltage

Battery level when the Aux load switches off

Aux Load on Battery %

or Voltage

Battery level when the Aux load switches on.

Solar Power

Power limiter to the maximum power allowed to the Aux load.

Gen Input

Tick this box if using a Generator.

Aux Load Output

Tick this box if using an Aux or Smart Load.

For Micro inverter Input

Tick this box if intending to connect a supplementary inverter or

micro inverter (Max. 4kW).

Zero Export

Tick this box to stop exporting power produced by the Aux Load.

Gen Peak Shaving

Tick this box to use peak power shaving.

5.21. Advanced Settings for Peak Shaving

To configure Peak Power Shaving function, click on the AUX LOAD icon.icon.

What this page displays:

Generator peak shaving is ON or OFF.

Peak Power Shaving value.

What you can do from this page:

Switch on the generator and/or grid
peak power saving and set the power
shaving value.

Peak Shaving:

This is a technique used to reduce electrical power consumption during periods

of maximum demand on the utility grid. This enables the user to save substantial amounts of
money due to the expensive peak power charges.

Содержание SUN-25K-SG01HP3-EU-BM2











































































Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды

SunSynk SUN-25K-SG01HP3-EU-BM2, Руководство по установке

Результаты поиска

Содержание SUN-25K-SG01HP3-EU-BM2

Отзывы:

Похожие инструкции для SUN-25K-SG01HP3-EU-BM2

Бренды по названию

Популярные бренды