Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 97 Скачать руководство пользователя

Страница: 97 / 120

Sedeo LITE Rev.A

Removing the quick release cushion from backrest

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instructions for removing the quick
release cushion from the backrest.

•

Rebuild the wheelchair in reverse order once completed.

•

Tightening torque for bolts is 6Nm.

Tools used

N/A

Fig. 6.4.53

Pull out and remove pin (A)

Fig. 6.4.54

Push down lever (B) and the backrest will become free

Fig. 6.4.55

Slide backrest cushion (C) up and remove from frame

Fig. 6.4.53

Fig. 6.4.54

Fig. 6.4.55

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды