Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 22 Скачать руководство пользователя

Страница: 22 / 120

Sedeo PRO + LITE Rev.A

Removal of calf pad and cushion from swing away legrest

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instruction for removing the calf pad
and cushion from a swing away legrest.

•

Rebuild the wheelchair in reverse order once completed.

•

T-nuts remain in the extrusion, they can be removed
through the wider slot section.

•

Tightening torque for bolts is 9Nm.

Tools used

Fig. 6.2.13 shows the starting position of the calf pad assembly

Fig. 6.2.14

Unscrew and remove (A) bolts from t-nuts in legrest assembly

Fig. 6.2.15 shows the calf pad from the rear of the assembly

Fig. 6.2.13

Fig. 6.2.14

Fig. 6.2.15

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды