Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 79 Скачать руководство пользователя

Страница: 79 / 120

Sedeo LITE Rev.A

Removing the release lever

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instructions for removing the release
lever from the legrest assembly.

•

Rebuild the wheelchair in reverse order once completed.

•

Tightening torque for bolts is 6Nm.

Tools used

Fig. 6.4.7

Use a punch to remove the axle (A) to release the lever

Fig. 6.4.8

Remove release lever (B) from legrest assembly and spring (C)

Fig. 6.4.9

Pull out and remove (D)

Fig. 6.4.7

Fig. 6.4.8

Fig. 6.4.9

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды