Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 38 Скачать руководство пользователя

Страница: 38 / 120

Sedeo PRO + LITE Rev.A

Fig. 6.2.51

Whilst pressing and holding the plastic pin, pull the footplate (D)

from the upper legrest assembly

To Reassemble

Fig. 6.2.52

Partially place the t-nuts into the footplate (E)

Please note the orientation of the t-nuts when reassembling

Fig. 6.2.53

Slide the rest of the assembly over the top of the footplate until

the t-nut is visible through the bottom hole (F). (The black plastic

pin may be needed to be pushed in again) and slide the footplate

assembly into the upper legrest assembly.

Fig. 6.2.54

Then set the footplate at the correct height. Re-fit 2 (A) bolts into

t-nuts.

Fig. 6.2.51

Fig. 6.2.52

Fig. 6.2.53

Fig. 6.2.54

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды