Sunrise Medical QUICKIE Q400 F Sedeo Lite Скачать руководство пользователя страница 95

Страница: 95 / 120

Sedeo LITE Rev.A

Fitting the recline receiver and manual/powered adjustable backrest options

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instructions for fitting the recline
receiver and manual/powered adjustable options to the
backrest.

•

Rebuild the wheelchair in reverse order once completed.

Tools used

Fig. 6.4.46

Fig. 6.4.47

Fig. 6.4.48

Fig. 6.4.46

This shows an exploded view of the recline receiver components

Fig. 6.4.47

Line up the receiver frame (A) with the two holes on the inside of

the shift piece

Fig. 6.4.48

Screw 2 (B) bolts in place on both sides of the seat

Tightening torque for bolts is 3Nm

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации, Страница: 95 / 120

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы: