Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 39 Скачать руководство пользователя

Страница: 39 / 120

Sedeo PRO + LITE Rev.A

Removal and reassembly of adjustment wheel set on tool adjustable legrest

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instruction for removing and
the reassembly of the adjustment wheel set on a tool
adjustable legrest.

•

Tightening torque for bolts is 9Nm.

Tools used

Fig. 6.2.55

Remove bolt (A) from the adjustment wheel set

Fig. 6.2.56

Remove axle (B) from the opposite side of the wheel set

Fig. 6.2.57

Pull apart upper section (C) from the lower section

NOTE: Spring used in the centre may be destroyed and need to be

replaced.

Fig. 6.2.55

Fig. 6.2.56

Fig. 6.2.57

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды