Sunrise Medical QUICKIE Q400 F Sedeo Lite Скачать руководство пользователя страница 106

Страница: 106 / 120

106

Sedeo ERGO Rev.A

Removing the backrest shell from the backrest

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instructions for removing the
backrest shell from the backrest.

•

Rebuild the wheelchair in reverse order once completed.

Tools used

Before completing, you must first remove the back cushion as illustrated

in Fig. 6.5.1

Fig. 6.5.13

Unscrew and remove 4 x (A) bolts from the backrest shell

Tightening for (A) bolts is 9Nm

Fig. 6.5.14

Remove backrest shell (B) from the backrest

NOTE: The JAY 3 Backrest shell can also be removed in the same way

by removing the same 4 x (A) bolts

Fig. 6.5.13

Fig. 6.5.14

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации, Страница: 106 / 120

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы: