Sunrise Medical QUICKIE Q400 F Sedeo Lite страница 18 Скачать руководство пользователя

Страница: 18 / 120

Sedeo PRO + LITE Rev.A

Removal of Whitmyer headrest and cushion from Whitmyer headrest mount

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instruction for removing the
Whitmyer headrest and cushion from the Whitmyer
headrest mount.

•

Rebuild the wheelchair in reverse order once completed.

•

Tightening torque for bolts is 10Nm.

Tools used

3/16”

Fig. 6.2.5

Slide off plastic cap (A)

Fig. 6.2.6

Loosen (B) bolts from crescent-shaped segment.

NOTE: Do not remove bolts fully.

Fig. 6.2.7

Remove 2 cresecent-shaped segments (C) and remove headrest

cushion (D)

Fig. 6.2.5

Fig. 6.2.6

Fig. 6.2.7

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Похожие инструкции для QUICKIE Q400 F Sedeo Lite

Бренды по названию

Популярные бренды