Sunrise Medical QUICKIE Q400 F Sedeo Lite Скачать руководство пользователя страница 64

Страница: 64 / 120

Sedeo PRO Rev.A

Removal of the actuator from powered adjustable backrest

Preparation

Note!

Switch off the wheelchair via remote control (power

wheelchair only).

Instructions

Note!

Suitable work area required!

•

Follow the illustrated instruction for removing the actuator
from a powered adjustable backrest unit

•

Rebuild the wheelchair in reverse order once completed.

•

Disconnect cables before taking apart.

•

Use small flat screwdriver to remove C-clips and pliers to
reinstall.

Tools used

Fig. 6.3.34 shows the starting position of the top bolt

Fig. 6.3.35

Remove bolt and C-clip, then slide out top bolt (A) from the left

side of the unit. Then remove C-clip and slide out bolt (B)

Fig. 6.3.36

Removing the bolts will allow you to partially remove the gas

strut (C) and actuator (D)

Fig. 6.3.34

Fig. 6.3.35

Fig. 6.3.36

Содержание QUICKIE Q400 F Sedeo Lite

























































































































Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы:

Sunrise Medical QUICKIE Q400 F Sedeo Lite, Инструкция по эксплуатации, Страница: 64 / 120

Результаты поиска

Содержание QUICKIE Q400 F Sedeo Lite

Отзывы: