FOLDING BACK– Zero Offset (Fig. A)
1.
Remove screw (2), nut (3), eccentric washer (4) and offset plastic
saddle (5) from backplate / back rest assembly.
2.
Aluminum
– Swap the 1-3/4" long screw (2) for a 1-7/8" long screw
(2A) and the "offset" plastic saddle (5) (with the step in it) for a plas-
tic saddle (5A) without offset (no step).
Titanium
– Swap the 1-7/8" long screw (2) for a 2" long screw (2A)
and the "offset" plastic saddle (5) (with the step in it) for a plastic
saddle (5A) without offset (no step).
3.
Holding plastic saddle (5A) against backrest tube, slide the sideguard
(6) and plastic washer (7) between the backplate (1) and the plastic
saddle(5A), as shown in Fig. A.
4.
Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic washer (7), plastic
saddle (5A) and backrest tube.
5.
Insert screw (2A) through the eccentric washer (4), backplate (1),
plastic washer (7), side guard (6), plastic saddle (5A) and backrest
tube. Attach nut (3).
6.
Align slot in side guard with hole in seat frame.
7.
Insert 1-7/8" long screw (8) through side guard bushing (9), plastic
washer (7), sideguard slot, 2nd plastic washer (7), plastic saddle
(5A), and seat frame. Attach nut (3A).
8.
Secure screws (2A & 8) and nuts (3 & 3A).
9.
Repeat procedure for opposite side.
10. Check backrest folding - if necessary, adjust tension in screw (8) and
nut (3A) to achieve proper folding function.
930494 Rev. A
13
E N G L I S H
E. SIDE GUARD INSTALLATION
Your Match Point has been assembled with either a "Folding" or "Fixed" backrest. Determine the configu-
ration of your chair and follow the appropriate installation instructions. Two mounting options are avail-
able for your side guards:
1. Zero Offset
The side guard width is the same as the seat frame width. The side guards mount inside the backplate.
2. 1/4" Offset
Seat frame width will be 1/2" wider with side guards (1/4" per side). The side guards mount outside the
backplate.
FOLDING BACK– 1/4" Offset (Fig. B)
1.
Remove screw (2), nut (3) and eccentric washer (4) from backplate /
backrest assembly.
2.
Aluminum
– Swap the 1-3/4" long screw (2) for a 2" long screw
(2A).
Titanium
– Swap the 1-7/8" long screw (2) for a 2" long screw (2A).
3.
Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic washer (7), plastic
saddle (5) and backrest tube.
4.
Insert 2" long screw (2A) through the side guard (6), plastic washer
(7), eccentric washer (4), backplate (1), plastic saddle (5) and back-
rest tube. Attach nut (3).
5.
Align slot in side guard with hole in seat frame.
6.
Insert a 2" long screw (2B) through side guard bushing (9), plastic
washer (7), sideguard slot, plastic washer (7), plastic saddle offset (5)
and seat frame. Attach nut (3A).
7.
Secure screws (2A & 2B) and nuts (3 & 3A).
8.
Repeat procedure for opposite side.
9.
Check backrest folding - if necessary, adjust tension in screw (2B)
and nut (3A) to achieve proper folding function.
Figure A – Folding Back, Zero Offset
Figure B – Folding Back, 1/4" Offset
Backrest
Tube
Seat
Frame
Backrest
Tube
Seat
Frame
