Sungrow ST2752UX Скачать руководство пользователя страница 54

Страница: 54 / 105

If the rollers are in the status below, raise left support 2 and right support 2.

•

Phase 3: End of platform bearing: It is recommended that the Pack is placed stably
and evenly on the platform as shown below.

step 7 Hoist and move the Pack: Fix the slings to the crane hook by top safety clips to lift and move

the Pack.

The PACK shall not be lifted by 1.5m higher than the ground to avoid falling.

step 8 Push in a new PACK.

Status confirmation: After the new PACK is landed on the platform surface, check

whether the PACK is aligned with the container, which can be confirmed by the guide
block at the end of the PACK. If the Pack is not aligned with the container door, lift and
adjust the Pack position, as shown below.

4 Common Maintenance Operations

Operation & Maintenance Instruction

Содержание ST2752UX










































































































Результаты поиска

Содержание ST2752UX

Отзывы:

Похожие инструкции для ST2752UX

Бренды по названию

Популярные бренды

Sungrow ST2752UX, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание ST2752UX

Отзывы:

Похожие инструкции для ST2752UX

Бренды по названию

Популярные бренды