Sun Microsystems Netra T5220 Скачать руководство пользователя

Страница: 133 / 178

Chapter 5

Replacing Chassis Components

5-3

FIGURE 5-2

Installing the Air Filter and Closing the Bezel

5.2

Replacing a Power Supply

The server’s redundant hot-swappable power supplies enable you to remove and
replace a power supply without shutting the server down provided that the other
power supply is online and working.

The following LEDs are lit when a power supply fault is detected:

■

Front and rear Service Required LEDs.

■

Amber Failure LED on the faulty power supply

If a power supply fails and you do not have a replacement available, leave the failed
power supply installed to ensure proper air flow in the server.

Содержание Netra T5220



















































































































































































Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды

Sun Microsystems Netra T5220, Руководство по обслуживанию

Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды