Sun Microsystems Netra T5220 Скачать руководство пользователя

Страница: 38 / 178

1-28

Sun Netra T5220 Server Service Manual • January 2012

service

Runs POST with preset values for

diag_level

and

diag_verbosity

diag_level

max

diag_mode

normal

, runs all the minimum

tests plus extensive CPU and memory tests.

min

diag_mode

normal

, runs minimum set of

tests.

diag_trigger

none

Does not run POST on reset.

user_reset

Runs POST upon user-initiated resets.

power_on_reset

Only runs POST for the first power on. This
option is the default.

error_reset

Runs POST if fatal errors are detected.

all_resets

Runs POST after any reset.

diag_verbosity

none

No POST output is displayed.

min

POST output displays functional tests with a
banner and pinwheel.

normal

POST output displays all test and informational
messages.

max

POST displays all test, informational, and some
debugging messages.

TABLE 1-7

ALOM CMT CLI Parameters Used for POST Configuration

(Continued)

Parameter

Values

Description

Содержание Netra T5220



















































































































































































Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды

Sun Microsystems Netra T5220, Руководство по обслуживанию

Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды