Sun Microsystems Netra T5220 Скачать руководство пользователя

Страница: 123 / 178

Chapter 4

Replacing Motherboard Assembly Components

4-35

4.9

Replacing the SCC Module

Note –

The SCC module is also known as the IDPROM chip.

Note –

The SCC module contains system host ID, MAC addresses, and configuration

variable settings for ILOM. If you are replacing a motherboard, you must move the
SCC module from the old motherboard to the new one.

Note –

If you are replacing a faulty SCC module, you must obtain the host ID, MAC

addresses, and ILOM configuration settings stored in the SCC module you are
replacing. Configure these settings into the new SCC module.

4.9.1

Removing the SCC Module

1. Prepare the server for SCC module removal.

See

Section 4.1, “Powering Off and Powering On the Server” on page 4-1

2. Remove the air duct.

See

Section 4.4.1, “Removing the Air Duct” on page 4-17

3. Remove the PCI mezzanine.

See

Section 2.3.6, “Removing the PCI Mezzanine” on page 2-9

4. Locate the SCC module.

5. Carefully pull the SCC module straight up from its connector.

4.9.2

Installing the SCC Module

1. Align the SCC module with its connector on the motherboard.

Note –

The SCC module and its connector are keyed.

2. Press the SCC module down until it seats.

Содержание Netra T5220



















































































































































































Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды

Sun Microsystems Netra T5220, Руководство по обслуживанию

Результаты поиска

Содержание Netra T5220

Отзывы:

Похожие инструкции для Netra T5220

Бренды по названию

Популярные бренды