manualshive.com logo in svg

Sun Microsystems 5220, Руководство по началу работы

Поделиться
Скачать
Sun Microsystems 5220 Скачать руководство пользователя страница 93

81

Glossary

array

(n.) Multiple disk drives that function as a single storage element and is
managed by the NAS appliance. The array consists of one controller unit and,
optionally, up to two expansion units.

AWG

(American wire gauge) (n.) A unit for measuring the thickness of wire.

back-end storage

The trays of disk drives. A tray with a RAID controller is called a controller
unit; a tray without a controller is called an expansion unit. See also controller
unit and expansion unit.

configuration

(1) (n.) The manner in which the software and hardware of an information
processing system are organized and interconnected. (2) (n.) The physical and
logical arrangement of programs and devices that make up a data processing
system. (3) (n.) The devices and programs that make up a system, subsystem,
or network.

controller unit

A RAID controller and up to 16 disk drives. See also expansion unit.

CIFS

Common Internet File System

driver

(n.) A software program that enables a computer to communicate with a
peripheral device.

DNS

Domain Name Service

expansion unit

A tray with up to 16 disk drives but no RAID controller. This type of unit
expands the capacity of an array and must be attached to a controller unit to
function. See also controller unit.

Fast Ethernet

(n.) A high-speed version of Ethernet transmitting data at 100 Mbps. Fast
Ethernet networks use the same media access control method that 10BASE-T
Ethernet networks use but achieve 10 times the data transmission speed.

FC

See Fibre Channel

Fibre Channel (FC)

A set of standards for a serial I/O bus capable of transferring data between
two ports at up to 100 MBytes/second. Fibre Channel supports point to point,
arbitrated loop, and switched topologies.

Содержание 5220





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды