Sun Microsystems 5220 Скачать руководство пользователя страница 62

Страница: 62 / 100

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

▼

To Connect to Optical Gigabit Ethernet
Networks

To connect the appliance to an optical Gigabit Ethernet network, the appliance must
have the optional optical Gigabit Ethernet card installed in PCI0.

FIGURE 3-7

shows the locations of the ports and the optical Gigabit Ethernet

connectors.

1. Connect a fiber optic cable from the network to the A connector on the card.

2. Connect a second fiber optic cable from the network to the B connector on the

card.

FIGURE 3-7

Connecting to an Optical Gigabit Network

Network ports have different identifiers in hardware and software. When you
configure the system (see

“Configuring the Appliance” on page 56

), the ports are

identified as described in the following table:

TABLE 3-1

Identifiers for Network Ports

Hardware
Identifier

Software
Identifier

Appliance

NET0

emc1

NET1

emc2

NET2

emc3

NET3

emc4

optical Gigabit Ethernet card

emf5

emf6

A B

NET

Содержание 5220





































































































Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды

Sun Microsystems 5220, Руководство по началу работы

Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды