manualshive.com logo in svg

Sun Microsystems 5220, Руководство по началу работы

Поделиться
Скачать
Sun Microsystems 5220 Скачать руководство пользователя страница 68

56

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

Configuring the Appliance

The Sun StorageTek 5220 NAS Appliance ships with the operating system installed.
To configure the appliance for the first time, complete the following tasks:

■

Provide an IP address

■

Use the Web Administrator’s Configuration Wizard.

Assigning the IP Address

You can assign an IP address in either of the following ways:

■

Using a Dynamic Host Configuration Protocol (DHCP) server to assign the IP
address automatically. Your network must have either a DHCP server or a DHCP
relay agent, which has access to a DHCP server on another network. The DHCP
server or agent assigns an IP address to the Sun StorageTek 5220 NAS Appliance
whenever it is powered on while connected to the network. If a DHCP server is
not available, you must assign the IP address manually.

■

Using the controls and liquid crystal display (LCD) panel on the Sun StorageTek
5220 NAS Appliance to enter the IP address manually.

▼

To Prevent an Address Assignment

If a DHCP server is available on your network but you prefer to assign the IP
address manually, you must prevent the appliance from acquiring an IP address
automatically by using the following procedure:

1. During the power-on sequence, wait for the following message to display in the

LDC panel: “DHCP Discovery NIC X”

2. Press any key on the LCD panel.

3. When the panel displays the message, “Abort DHCP?” press the ENTER button

on the panel to confirm.

4. Follow the instructions in

To Assign the IP Address Manually

.

▼

To Assign the IP Address Manually

If a DHCP server is not available or if you prefer to assign a permanent IP address to
the appliance, configure the IP address using the LCD panel.

Содержание 5220





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды