Sun Microsystems 5220 Скачать руководство пользователя страница 66

Страница: 66 / 100

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

▼

To Power On the Appliance, Controller Unit,
and Expansion Units Initially

Note –

If you have one or more expansion units, you must use this initial power-on

sequence. If you do not have any expansion units, you must use the procedure
described in

“To Power On the Appliance and Controller Unit Initially” on page 52

1. Verify that all cables between the Sun StorageTek 5220 NAS Appliance, controller

unit, and expansion units are secured according to the instructions in

“Connecting

the Appliance to the Controller Unit” on page 44

and

“Connecting a Controller Unit

to Expansion Units” on page 46

2. Power on the controller unit by toggling the two power supply switches to the On

position.

3. Wait for all LEDs on the controller unit’s front panel to turn solid green,

indicating good operation. This takes about three minutes.

4. Power on the first expansion unit by toggling the two power supply switches to

the On position.

5. Wait for all LEDs on the expansion unit’s front panel to turn solid green,

indicating good operation.

6. If you have a second expansion unit, set both of its power supply switches to the

On position. Wait for all LEDs on the front panel to turn solid green.

7. After you have powered on the expansion units, wait 5 minutes for all units to be

identified and mounted and then proceed.

8. Verify that the appliance is connected to the network by checking that the green

LED on the appliance’s network connection is lit.

9. Power on the appliance by pressing the recessed Power button located on the

front panel. Using a pen tip or similar implement, press the recessed Power
button on the appliance’s front panel, as shown in

FIGURE 3-8

Содержание 5220





































































































Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды

Sun Microsystems 5220, Руководство по началу работы

Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды