manualshive.com logo in svg

Sun Microsystems 5220, Руководство по началу работы

Поделиться
Скачать
Sun Microsystems 5220 Скачать руководство пользователя страница 24

12

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

Preparing the Cabinet

Note –

The rack must have an AC power disconnect. This power source disconnect

must be easily accessible, and it must be labeled as controlling power to the entire
rack, not only to the appliance

Be sure the location of the cabinet or rack complies with the following requirements
and that it has been installed as described in its installation instructions:

■

Check that the rack or cabinet has unrestricted air flow for the cooling fans.

■

Check that the maximum ambient operating temperature in the rack does not
exceed 95˚F (35˚C).

■

Make sure that the rack will not tip over, even when the controller and expansion
units are fully extended from the rack.

■

Make sure the rack has two power sources connected to two separate power
circuits.

■

Make sure the power outlets are close enough to the units for the power cords to
reach the cabinet properly.

■

Make sure the power cables are grounded.

Before you begin mounting the rail kits, do the following:

1. Stabilize the cabinet as described in the cabinet documentation.

2. If the cabinet has casters, make sure the casters are locked to prevent the cabinet

from rolling.

3. Remove or open the front panel.

4. Remove or open the vented back panel.

Note –

Sun Microsystems makes no warranties or guarantees as to fit, form, or

function of the Sun StorageTek 5220 NAS Appliance system installed in third-party
racks or cabinets. It is the customer’s responsibility to ensure that the rack or cabinet
can house the Sun StorageTek 5220 NAS Appliance system in all conditions that
might exist. All racks and cabinets must comply with local building and construction
codes.

Содержание 5220





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды