manualshive.com logo in svg

Sun Microsystems 5220, Руководство по началу работы

Поделиться
Скачать
Sun Microsystems 5220 Скачать руководство пользователя страница 28

16

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

Planning the Installation

At a minimum, the system has an appliance and the controller unit. Your system can
have one or two expansion units, installed now or at a later date. Plan the placement
of the rails carefully because they are spaced differently, depending on whether you
are installing a unit or an appliance.

In general, the installation is accomplished in the following order:

1. Install the universal slide rail kit for the controller unit, starting at the bottom of

the rack.

2. Install the universal slide rail kit for each expansion unit, starting above the

controller unit.

3. Mount the controller unit at the bottom of the cabinet.

4. Mount each expansion unit, from the bottom up.

5. Install the slide rails for the appliance.

6. Install the cable management kit.

7. Mount the appliance.

8. Install the power cords.

Caution –

The controller and expansion units must be installed in the cabinet

starting from the bottom up to distribute the weight correctly in the cabinet. The
appliance is installed last. Uneven loading of the rack can cause dangerous
instability.

Note –

Some procedures require two people to complete.

Содержание 5220





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды