Sun Microsystems 5220 Скачать руководство пользователя страница 67

Страница: 67 / 100

Chapter 3

Connecting the Sun StorageTek 5220 NAS Appliance

▼

To Power On the System After a Shutdown

Use this procedure to power the system on again after it has been running and then
powered off. If the system has never been powered on before, use the procedure
described in

“To Power On the Appliance and Controller Unit Initially” on page 52

“To Power On the Appliance, Controller Unit, and Expansion Units Initially” on

page 54

Note –

When you power off the controller units and expansion units, wait five

seconds before you power them back on. If you power the units off and on too
quickly, unexpected results can occur.

1. Verify that all cables between the Sun StorageTek 5220 NAS Appliance, controller

units, and expansion units are secured according to the instructions in

“Connecting the Appliance to the Controller Unit” on page 44

and

“Connecting a

Controller Unit to Expansion Units” on page 46

2. Power on each expansion unit by setting the two power supply switches to the On

position. Wait at least 30 seconds after powering on the second expansion unit, if
your system has one.

3. Power on the controller unit by setting the two power supply switches to the On

position.

4. Check that all LEDs on the controller unit’s front panels have turn solid green,

indicating good operation.

5. Check that all LEDs on the expansion unit’s front panels have turn solid green,

indicating good operation.

6. Verify that the appliance is connected to the network by checking that the green

LED on the appliance’s network connection is lit.

7. Power on the appliance by pressing the recessed Power button located on the

front panel. Using a pen tip or similar implement, press the recessed Power
button on the appliance’s front panel, as shown in

FIGURE 3-8

Содержание 5220





































































































Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды

Sun Microsystems 5220, Руководство по началу работы

Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды