Sun Microsystems 5220 Скачать руководство пользователя страница 64

Страница: 64 / 100

Sun StorageTek 5220 NAS Appliance Getting Started Guide • October 2006

▼

To Power On the Appliance and Controller Unit
Initially

Note –

If you also have one or more expansion units, you must use the procedure

described in

“To Power On the Appliance, Controller Unit, and Expansion Units

Initially” on page 54

1. Verify that all cables between the Sun StorageTek 5220 NAS Appliance and the

controller unit are secured according to the instructions in

“Connecting the

Appliance to the Controller Unit” on page 44

2. Power on the controller unit by toggling the two power supply switches to the On

position.

3. Wait for all LEDs on the controller unit’s front panel to turn solid green,

indicating good operation. This takes about four minutes.

4. Verify that the Sun StorageTek 5220 NAS Appliance is connected to the network

by checking that the green LED on the appliance’s network connection is lit.

Содержание 5220





































































































Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды

Sun Microsystems 5220, Руководство по началу работы

Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды