Sun Microsystems 5220 Скачать руководство пользователя страница 45

Страница: 45 / 100

Chapter 2

Installing the Appliance and Back-End Storage

8. Use the slide rail spacing tool to adjust the distance between the slide rails:

a. At the front of the rack, insert the left side of the tool into slots at the end of

the left rail (

FIGURE 2-17

FIGURE 2-17

Adjusting the Distance Between the Slide Rails

b. Insert the right side of the tool into the front end of the right rail, while sliding

the end of the rail to the right or left as needed to allow the ends of the tool to
enter the ends of both rails. The distance between the rails is now equal to the
width of the appliance with its mounting brackets.

c. Tighten the screws to lock the ends of the rails in place.

d. At the back of the rack, repeat

Step a

through

Step c

for the back ends of the

rails.

Содержание 5220





































































































Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды

Sun Microsystems 5220, Руководство по началу работы

Результаты поиска

Содержание 5220

Отзывы:

Бренды по названию

Популярные бренды