manualshive.com logo in svg

Sun Microsystems 5220, Руководство по началу работы

Поделиться
Скачать
Sun Microsystems 5220 Скачать руководство пользователя страница 23

Chapter 2

Installing the Appliance and Back-End Storage

11

Slide Rail Kit for the Appliance

The Sun StorageTek 5220 NAS Appliance is supported with the slide rail kit (370-
7669-02) and cable management arm (370-7668-02). The slide rail kit contains four-
point mounted slide rails and is designed to enable the Sun StorageTek 5220 NAS
Appliance to be installed in the Sun Rack™ 900, the Sun Rack 1000, and other
ANSI/EIA 310-D-1992 or IEC 60927 compliant racks. No other kits are available to
allow two-point, front-mount, or mid-mount installation.

The slide kit includes hardware that enables mounting to any of the following types
of rails:

■

6-mm threaded holes

■

No. 10-32 threaded holes

■

No. 10 clearance holes

■

Square unthreaded holes compliant with EIA and IEC standards

Universal Rail Kit for Back-End Storage

Use the universal rail kit to mount the controller and expansion units in any
standard Sun cabinet, such as the Sun Rack 900/1000 cabinet.

Preparing for the Installation

Use the following procedures to prepare for installation:

■

“Preparing the Cabinet” on page 12

■

“Proper Grounding Technique” on page 13

■

“Checking the Slide Rail Kit” on page 14

■

“Checking the Universal Rail Kit” on page 14

■

“Checking the Controller and Expansion Units” on page 15

■

“Checking the Appliance” on page 15

■

“Preparing the Cabinet” on page 12

Содержание 5220





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды