manualshive.com logo in svg

Strata CIX 200, Руководство по программированию


Поделиться
Скачать
background image

Data Backup and Restore

Local Update

Strata CIX Programming Vol.1    12/09

14-11

CAUTION!

This operation will take the system out of service for 10 minutes to an hour or more 
depending on the CIX database. Do not skip any steps or the Update will fail.

Notes

•

If CLRREBOOT is activated without the Backup data SmartMedia card installed, the active and 
standby software is swapped and the system default program data is restored. 

•

The Strata CIX processor heartbeat LED stops flashing and all telephones become inactive. After 
a few minutes the Strata CIX initializes and starts up with new version of software as active and the 
original software as standby, and then restores the backed up program data from the SmartMedia 
card default.dat file (the processor SmartMedia LED flashes while it restores the program data to 
the processor RAM). 

•

After CLRREBOOT has completed the new version of CIX System software will be active in Trial 
mode.

•

If system power is turned off/on while the Active side of flash memory is in the Trial mode, the 
original software switches back to active and the new software will switch back to Standby. This is 
to provide an automatic method of switching back to the original software version if the new 
version is causing problems.

7.

Confirm that the software is updated and the Backup data is restored by verifying/doing the following:

•

Make sure the processor SmartMedia LED is off.

•

Log in to programming mode from a digital telephone. If you cannot log in, it means the data restore 
process is not completed.

•

From the programming telephone, in Program 901 make sure that the new Strata CIX system 
software version number is on the active side. 

FB01

 shows the new system software version 

number on the active side, and 

FB02

 shows the original software version number on standby side.

8.

Set the Active side of flash RAM from “Trial” to “Normal” as follows:

•

From the programming telephone, enter Program 911 and press 

Hold

. Press 

FB04

 and dial 

1

 

(NORMAL), then press 

Hold

. The new software is on the active side running in Normal mode.

•

If Strata CIX power is turned off/on before the Active side is switched to “Normal”, the Strata CIX will 
automatically perform a CLRREBOOT and make the old software active.

Note

The active side switches from “Trial” to “Normal” automatically after 24 hours if it is not done 
manually using Program 911.

9.

Remove the SmartMedia card and turn the power off for 5 seconds and then back on to reset BIPU-M, 
BIPU-Q, QISG, ISDN and other advanced features.

10. Test the system to verify that the new software is running properly by checking dial tone, making 

incoming and outgoing calls, internal and external calls and all other peripherals, such as voice mail, 
etc., are working correctly.

11. Toshiba recommends that the SmartMedia card containing the customer data remains installed on the 

CIX processor. This enables you to make and backup changes using Network eManager remotely.

Important!

It is your responsibility to verify the system is working correctly after local Update is 
complete.

Содержание CIX 200





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CIX 200

Samsung SPH-I300SS Tips/Troubleshooting Manual preview
SPH-I300SS
Бренд: Samsung Страницы: 22
qua Phone PX Settings Manual preview
Phone PX
Бренд: qua Страницы: 2
Sony Ericsson Xperia X10 Extended User Manual preview
Xperia X10
Бренд: Sony Ericsson Страницы: 113
E-MetroTel XSTIM Infinity Phone User Manual preview
XSTIM Infinity Phone
Бренд: E-MetroTel Страницы: 21
Iget BLACKVIEW GBV7000 Pro Quick Start Manual preview
BLACKVIEW GBV7000 Pro
Бренд: Iget Страницы: 47
TIPTEL INNOVAPHONE 200 Operating Manual preview
INNOVAPHONE 200
Бренд: TIPTEL Страницы: 32
Westell A99-WMTA3030-01 Quick Start Manual preview
A99-WMTA3030-01
Бренд: Westell Страницы: 12
Yealink SIP-T31 Quick Start Manual preview
SIP-T31
Бренд: Yealink Страницы: 8
Inter-Tel AXXESS 8560 User Manual preview
AXXESS 8560
Бренд: Inter-Tel Страницы: 86
Samsung Moment SPH-M900 User Manual preview
Moment SPH-M900
Бренд: Samsung Страницы: 122
Samsung My Shot SCH-r430 series User Manual preview
My Shot SCH-r430 series
Бренд: Samsung Страницы: 142
Samsung Mesmerize SCH-I500 Manual Del Usuario preview
Mesmerize SCH-I500
Бренд: Samsung Страницы: 170
Samsung Messager SCH-r450 Series User Manual preview
Messager SCH-r450 Series
Бренд: Samsung Страницы: 150
Samsung MYTHIC SGH-A897 Series Manual Del Usuario preview
MYTHIC SGH-A897 Series
Бренд: Samsung Страницы: 202
Samsung Messager Touch SCH-R631 Manual Del Usuario preview
Messager Touch SCH-R631
Бренд: Samsung Страницы: 165
Samsung MYTHIC SGH-A897 Series User Manual preview
MYTHIC SGH-A897 Series
Бренд: Samsung Страницы: 202
Samsung M620 - SPH UpStage Cell Phone Manual preview
M620 - SPH UpStage Cell Phone
Бренд: Samsung Страницы: 340
Samsung Moment SPH-M900 Manual Del Usuario preview
Moment SPH-M900
Бренд: Samsung Страницы: 224

Бренды по названию

Популярные бренды

Загрузить еще бренды