manualshive.com logo in svg

Strata CIX 200, Руководство по программированию


Поделиться
Скачать
background image

IP Telephone Programming

IP Telephone Installation and Network Connection Setup

Strata CIX Programming Vol.1    12/09

8-19

IP T

e

le

phone

 

Pr
ogra

mming

09 Display Software 

Version Number of IP 
Telephone

This is read-only. If any problem occurs it is useful to analyze the problem with 
this version. A sample software version is DIP11NA. DIP1 represents the IP 
telephone model; 1NA represents software version of the IP telephone; 1N 
represents the version of updatable software and A means the version of not-
updatable software (BootROM). 

Possible values:Max. 16 ASCII characters

10 SIP Terminal URI

Set the Uniform Resource Identifier of the SIP terminal. URI is to identify the IP 
telephone in the system. You can use A-Z, a-z and 0-9 up to 32 characters as 
the URI. It has to be unique in the system.

Possible values:Max 32 ASCII characters

11 SIP Terminal Password

Set password for terminal authentication of the SIP terminal. This password is 
checked for terminal authentication when registration is performed from the SIP 
terminal. You can use A-Z, a-z and 0-9 up to 64 characters. It doesn't have to be 
unique in the system, and same password can be assigned to plural SIP 
terminals.

12 IP Sta KeepAlive Timer

Keep-alive timer for station for full IP station.

Possible values:0 ~ 60 seconds

13 Station IP DTMF 

Translation Mode

DTMF translation mode for full IP station.

Possible values:Tone (Default), Outband or Inband

Note

This parameter is not supported in CIX.

14 Secondary Audio Codec 

for Full IP station

IP telephones have two built-in codecs. Select the audio codec that should be 
used in this IP telephone.

The G.711codec - provides the highest voice quality but uses the most network 
bandwidth (about 115kbps per IP telephone when in use).

The G.729A codec - provides less voice quality but uses the least amount of 
network bandwidth (about 29kbps per IP telephone when in use).

High traffic or low speed networks may require the IP Telephones to use G729A.

Example:

If installing remote IP telephones connected to Cable or DSL lines, the upstream 
rate is usually restricted and may not provide a consistent upstream bandwidth 
(advertised as 128kbs but is normally less because of traffic) so the G729a 
codec would probable be the best choice for this situation.

The Voice Packet Table Prog 250-07 and the VP Table's voice packet 
parameters Prog 152 must be set properly for the codec assigned.

Possible values:G711, G729A (Default), None

15 Secondary Voice Packet 

Index

CIX provides peer to peer connection when an IP telephone directly 
communicates with another IP telephone. A negotiation method is required to 
resolve differing audio codec settings on the IP telephones. When a call is 
established between IP telephones, the CIX will check the assignment of 
secondary audio codecs. If there is matching assignment, it will be applied. If 
there is not, the user will hear reorder tone.

Possible values:1 ~ 128

F

IELD

D

ESCRIPTION

Содержание CIX 200





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CIX 200

T-Mobile Sidekick 3 Start Manual preview
Sidekick 3
Бренд: T-Mobile Страницы: 4
Galaxy A21 Notes On Usage preview
A21
Бренд: Galaxy Страницы: 58
Talkaphone VOIP-500 Series Integration Manual preview
VOIP-500 Series
Бренд: Talkaphone Страницы: 4
Talk-a-Phone VOIP-600 Series Quick Installation Manual preview
VOIP-600 Series
Бренд: Talk-a-Phone Страницы: 6
Talkaphone VOIP-500 Series Quick Installation Manual preview
VOIP-500 Series
Бренд: Talkaphone Страницы: 6
TAG Heuer meridiist User Manual preview
meridiist
Бренд: TAG Heuer Страницы: 49
M4TEL SS1090 Quick Start Manual preview
SS1090
Бренд: M4TEL Страницы: 22
Icemobile TWILIGHT II User Manual preview
TWILIGHT II
Бренд: Icemobile Страницы: 19
Xblue Networks IP7g User Manual preview
IP7g
Бренд: Xblue Networks Страницы: 98
Polycom SP501 Quick Start Manual preview
SP501
Бренд: Polycom Страницы: 2
iBall Vogue 2.8a SLEEC User Manual preview
Vogue 2.8a SLEEC
Бренд: iBall Страницы: 23
Yealink SIP-T30 Quick Start Manual preview
SIP-T30
Бренд: Yealink Страницы: 28
Doro PHONEEASY 505 Manual preview
PHONEEASY 505
Бренд: Doro Страницы: 48
Audiovox Technophone PC200 User Manual preview
Technophone PC200
Бренд: Audiovox Страницы: 12
Argos Bush Spira C2 Instruction Manual preview
Bush Spira C2
Бренд: Argos Страницы: 23
Samsung SM-G318HZ/DS User Manual preview
SM-G318HZ/DS
Бренд: Samsung Страницы: 92
Samsung SM-E500F/DS User Manual preview
SM-E500F/DS
Бренд: Samsung Страницы: 132
Samsung SM-A750FN/DS User Manual preview
SM-A750FN/DS
Бренд: Samsung Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды