manualshive.com logo in svg

Strata CIX 200, Руководство по программированию


Поделиться
Скачать
background image

Operation

License Control

Strata CIX Programming Vol.1    12/09

10-15

Oper

ation

License Activate

Prerequisite Program:

License Issue, above

This program enables activation of Network eManager licenses issued in License Issue.

License Information

The following programs enable you to set up Licensing details for Network eManager users.

Prerequisite Program:

None

1. Select Mainteance > Licensing > License Information.

2. View Equipped License Information details for this Strata CIX account.

This view is read-only information.

F

IELD

D

ESCRIPTION

Delay Timer

Select Activation Delay Timer in hours.

Possible values:0~24 (default = 0)

Notes

•

Enter 

0 

to issue or activate the license immediately or 1~24 to set the 

automatic delay activation feature, where 1 = 1 hour delay; 2 = 2 hour delay, 
etc.

•

After the license is activated, use the License Information screen below to 
check that all ports and features have been activated properly.

F

IELD

D

ESCRIPTION

CIX/CTX Release 
Number

This is the Basic Release Number of CIX software. To view the Active Software 
Version, go to Operations/System Setup.

System Type

This identifies the type of CIX system to which Strata eManager is currently 
connected.

Maximum Number 
of Cabinets

This identifies the maximum number of cabinets. The total of base plus 
expansion cabinets.

Number of Serial 
Ports

This identifies the number of serial ports licensed on the BSIS. 

One license is needed for each SMDR and SMDI device connected to BSIS. 

(Programs 803 and 804 assigns BSIS ports).

Number Of DTMF 
Receivers

This identifies the number of DTMF receivers licensed. The ARCS 
Subassembly is required on the CIX100 processor, no additional hardware is 
required for CIX670 or CIX1200.

Содержание CIX 200





























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CIX 200

O2 XM User Manual preview
XM
Бренд: O2 Страницы: 72
NEC DT730 User Manual preview
DT730
Бренд: NEC Страницы: 216
Samsung Galaxy A14 5G User Manual preview
Galaxy A14 5G
Бренд: Samsung Страницы: 145
Ericsson IP Vision Dialog 4425 User Manual preview
IP Vision Dialog 4425
Бренд: Ericsson Страницы: 136
Fysic FM-7810 Quick Start Manual preview
FM-7810
Бренд: Fysic Страницы: 8
Ipevo WKPCSPN-01IP Quick Start Manual preview
WKPCSPN-01IP
Бренд: Ipevo Страницы: 21
Alcatel One Touch Spop 4030D User Manual preview
One Touch Spop 4030D
Бренд: Alcatel Страницы: 73
Docomo Digital Mova SO503iS HYPER Manual preview
Digital Mova SO503iS HYPER
Бренд: Docomo Страницы: 396
TIPTEL Ergophone 6050 Operating Instructions Manual preview
Ergophone 6050
Бренд: TIPTEL Страницы: 52
Vertu MMII Quick Manual preview
MMII
Бренд: Vertu Страницы: 73
TIPTEL INNOVAPHONE 200 Operating Manual preview
INNOVAPHONE 200
Бренд: TIPTEL Страницы: 32
Sagem myC-1 Owner'S Manual preview
myC-1
Бренд: Sagem Страницы: 61
switel M 180 Quick Start Manual preview
M 180
Бренд: switel Страницы: 4
Samsung SGH T319 Manual Del Usuario preview
SGH T319
Бренд: Samsung Страницы: 182
Samsung SGHP735 User Manual preview
SGHP735
Бренд: Samsung Страницы: 193
Samsung SGH T349 Information Manual preview
SGH T349
Бренд: Samsung Страницы: 2
myPhone POCKET PRO User Manual preview
POCKET PRO
Бренд: myPhone Страницы: 41
Sharp GC40K Manual preview
GC40K
Бренд: Sharp Страницы: 324

Бренды по названию

Популярные бренды

Загрузить еще бренды