Stihl FC 75 Скачать руководство пользователя страница 48

Страница: 48 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

– Remove the shroud,

5.1

– Carry out leakage test,

9.2.1

Take out the screws (1).

– Remove the end cover with cap.

936RA023

Take the cap out of the end cover.

932RA285

Remove the flange.

936RA024

Inspect the metering diaphragm
and gasket and replace if
necessary,

9.3.3

Install in the reverse sequence.

936RA025

– Remove flange secured with an

oval end cover,

9.3.1

– Remove flange secured with a

square end cover,

9.3.2

Remove the metering
diaphragm (1) and gasket (2)

936RA026

from the carburetor body.

If the gasket and diaphragm are
stuck together, remove and
separate them very carefully.

Inspect the diaphragm and
gasket and replace if necessary.

The diaphragm is a very delicate
component. As a result of the
alternating stresses the material
eventually shows signs of fatigue,
i.e. the diaphragm distorts and
swells and has to be replaced.

Install in the reverse sequence.

9.3.2

Flange Mounting with Square End Cover

9.3.3

Metering Diaphragm

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды