manualshive.com logo in svg

Stihl FC 75, Руководство по обслуживанию

Поделиться
Скачать
Stihl FC 75 Скачать руководство пользователя страница 43

42

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

The carburetor’s throttle lever must 
butt against the stop on the 
carburetor cover when the throttle 
trigger is fully depressed (full 
throttle) and against the idle speed 
screw (LA) when the throttle trigger 
is released (idle position).

– Remove the shroud, 

b

 5.1

Version with Control Handle 
up to 2002 only

– To adjust, squeeze the throttle 

trigger as far as stop (full throttle 
position).

:

Turn the adjusting screw (1) 

VA

932RA314

2

3

1

4

clockwise until the throttle lever 
(2) butts against the stop (3) on 
the carburetor cover.

:

Release the throttle trigger (idle 
position). The throttle lever must 
butt against the idle speed screw 
(4).

Version with Control Handle 
from 2002 only

The throttle cable is 

no longer

 

adjusted at the tensioner. However, 
if the basic setting of the automatic 
throttle cable adjuster does not 
produce a satisfactory result, rotate 

VA

936RA377

1

the adjusting screw slightly.

– Remove the shroud, 

b

 5.1

:

Before starting the adjustment, 
center the adjusting screw (1) as 
shown.

Install in the reverse sequence.

Dirty air filters reduce engine power, 
increase fuel consumption and 
make starting more difficult. The air 
filter must be cleaned if there is a 
noticeable loss of engine power.

– Close the choke shutter.

– Remove all loose dirt from 

around the filter housing and 
cover.

:

Push back the tab on the filter 
housing.

:

Pull of the filter cover.

VA

936RA156

:

Remove the foam element (1) 
and felt element (2).

VA

936RA157

1

2

8.8

Adjusting the Throttle 
Cable

9.

Fuel System

9.1

Air Filter

Содержание FC 75







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды