Stihl FC 75 Скачать руководство пользователя страница 23

Страница: 23 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Thread the starter rope through
the hole in the side of the rotor.

– Secure the rope with a simple

overhand knot.

936RA050

Pull the rope back into the rotor
until the knot locates in the
recess.

Press the end of the rope into the
slot.

– Install the rope rotor,

6.3

936RA051

– Tension the rewind spring,

6.3.1

Assemble all other parts in the
reverse sequence.

– Unscrew the spark plug and

block the piston with the locking
strip 0000 893 5903,

5.2

– Remove the rewind starter,

6.2

Unscrew the carrier from the

936RA053

crankshaft.

Squeeze the ends of the pawl’s
peg together.

– Take the pawl out of the carrier.

936RA054

Take the torsion spring (arrow) off
the pawl.

936RA055

Push the torsion spring over the
new pawl.

936RA056

6.6

Carrier/Pawl

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды