Stihl FC 75 Скачать руководство пользователя страница 60

Страница: 60 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Place the loop handle (1) on the
drive tube (2).

Position the clamp block (3)
against the drive tube and slide it
into the loop handle.

936RA202

Fit the square nut (arrow).

– Insert the screw and tighten it

down moderately.

936RA203

Position the loop handle about
15 cm (distance “A“) forward of
the control handle and tighten it
down firmly.

Assemble all other parts in the
reverse sequence.

936RA204

The drive shaft is supported inside
the drive tube in a flexible liner. The
ends of the flexible liner are sealed
with plugs.

– Remove the bearing housing/

gearbox – see "CombiTools"
service manual.

Drive shaft in FC 85, FH 75, FS 85,
HL 75, KW 85

Pull the rigid drive shaft out of the
drive tube.

FS 85 only

936RA205

A hollow lightweight shaft with a
diameter of 8 mm was installed in
the FS 85 for a period. If the drive
shaft is faulty, use the 6 mm
diameter solid shaft as a
replacement. Make sure the flexible
liner is changed at the same time.

The 8 mm diameter hollow
lightweight shaft is still used, but
only in the FS 85 RX (USA/CAN
version).

Drive shaft in FS 75, 80, FC 75

Pull the flexible drive shaft out of
the drive tube.

Drive shaft (all models)

936RA206

If the drive shaft has turned blue,
always install a new one.

All models except FS 75

– Coat the drive shaft with STIHL

gear lubricant for hedge
trimmers,

12, before installing

it in the drive tube.

FS 75 only

– Coat the drive shaft with STIHL

gear lubricant for brushcutters,

12, before installing it in the

drive tube.

Apply the lubricant uniformly to the
drive shaft.

Never

pump lubricant

directly into drive tube.

10.3

Drive Shaft/Flexible Liner

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды