Stihl FC 75 Скачать руководство пользователя страница 27

Страница: 27 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

To avoid the risk of electrocution, do
not start the engine while the control
handle is exposed.

FC 75, FS 75, 80, 85, HL 75 only

Take the screws (arrows) out of
the outer half of the handle
molding.

– Remove the handle molding.

936RA119

Carefully remove the rivet
(interlock lever) from the outer
handle molding.

936RA121

Remove the interlock lever from
the pivot.

936RA122

Remove the torsion spring from
the pivot.

936RA123

Take out the clamp screws
(arrows).

– Remove the inner handle

molding from the drive tube.

936RA124

Disconnect throttle cable nipple
from the throttle trigger.

– Pull the throttle trigger off the

drive tube.

936RA125

Remove the torsion spring (arrow
- if fitted) from the pivot.

Install in the reverse sequence.

936RA126

Push the throttle trigger (facing
the engine) onto the drive tube.

The bent leg of the torsion spring
must engage the slot in the throttle
trigger.

936RA434

Throttle Control

8.1

Control Handle on Loop Handle up to 1997

8.1.1

Throttle Trigger / Interlock Lever

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды