manualshive.com logo in svg

Stihl FC 75, Руководство по обслуживанию, Страница: 66 / 70

Поделиться
Скачать
Stihl FC 75 Скачать руководство пользователя страница 66

65

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

:

Remove the washer (if fitted) 
from the output shaft.

– Carefully drive both needle 

sleeves out of the bearing 
housing.

Install in the reverse sequence.

VA

936RA355

Carry out the following operations 
carefully.

:

Press home the plain bearing 
until the shoulder (1) of the press 
arbor (2) 4119 893 7200 butts 
against the bearing housing (3).

VA

935RA356

3

1

2

:

Press home the needle sleeve 
until the press arbor (1) 
4119 893 7200 butts against the 
bearing housing (2).

VA

936RA357

2

1

:

Push the bearing housing onto 
the drive tube. Make sure the 
holes (arrows) are in alignment.

– Insert the fixing screw and tighten 

it down firmly.

VA

936RA358

:

Line up the recess (arrow) in the 
neck of the deflector with the 
bead on the bearing housing and 
then push home the deflector as 
far as stop.

– Tighten down the clamp screws 

firmly, 

b

 3.2

VA

936RA359

Содержание FC 75







































































Отзывы:

Нет отзывов