Stihl FC 75 Скачать руководство пользователя страница 49

Страница: 49 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Fit the gasket (1) on the
carburetor body.

Line up the hole in the gasket (2)
with the compensating bore in the
carburetor.

936RA027

Place metering diaphragm (1) on
the gasket.

Line up the hole in the metering
diaphragm with the compensating
bore in the carburetor and gasket.

Reassemble other parts,

9.2.2

936RA028

– Remove the metering

diaphragm,

9.3.3

Take out the screw (1).

936RA029

Carefully lift away the inlet control
lever (1) with spindle.

Install in the reverse sequence.

– Engage clevis in annular groove

on head of the inlet needle.

936RA030

– The spring must locate in the

control lever’s nipple.

Check that inlet needle and spring
are properly seated.

Install in the reverse sequence.

– Remove the metering

diaphragm,

9.3.3

Take care not to damage the fixed
jet with the screwdriver.
The fixed jet cannot be removed on
carburetors not listed below. Clean
the jet or replace the carburetor if
necessary.

C1Q-S63, C1Q-S69, C1Q-S78 and
C1Q-S80 carburetors

Use a suitable screwdriver to
unscrew the fixed jet (1).

C1Q-S60, C1Q-S56, C1Q-S45
carburetors

936RA031

Use a suitable screwdriver to
unscrew the fixed jet (1).

Install in the reverse sequence.

936RA225

9.3.4

Inlet Needle

9.3.5

Fixed Jet

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды