Stihl FC 75 Скачать руководство пользователя страница 62

Страница: 62 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Press down the lock button
(arrow) and hold it in that
position.

Pull out the drive shaft (1)
together with the sleeve (2).

936RA061

Pull out the clips (1).

If the sleeve (2) is fitted, heat it
with a hot air blower.

– Remove the sleeve.

If the drive shaft has turned blue,

936RA062

always install a new one.

Push the sleeve (1) onto the drive
shaft (2).

Press the sleeve (3) on to the
knurling.

– Fit the clips.

936RA063

– Before installing the drive shaft,

coat it with STIHL gear lubricant
0781 120 1109,

12.

Apply the lubricant evenly to the
drive shaft.

Never

pump lubricant

directly into the drive tube.

Push the drive shaft (1) with
sleeve (2) into the drive tube.

Press down the lock button
(arrow) and push the sleeve (2)
home as far as stop.

936RA064

Push the coupling sleeve (1) onto
the drive tube (2) as far as stop.

Line up the coupling sleeve so that
the slot engages the lug and the gap
in the clamp points down.

Tighten down the clamp screw

936RA065

(3) firmly.

– Fit the drive tube.

– Tighten down the wing screw

firmly.

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды