Stihl FC 75 Скачать руководство пользователя страница 31

Страница: 31 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

– Tighten down the clamp screws

firmly,

3.2

The slot (1) in the slide control
must engage over the outer edge
(2) of the handle molding.

Torsion spring (3) must locate in

recess (4) in slide control.

– Remove the shroud,

5.1

Take out the screw (1).

Remove the extended throttle
cable (2).

936RA115

2 1

Disconnect throttle cable nipple
(1) from slotted pin (2) on
carburetor’s throttle lever.

936RA116

2
1

Pull the throttle cable out of the
tensioner.

936RA117

Pull the short circuit wire
connector off the tag on the
ignition module.

– Remove the throttle trigger,

8.2.1

936RA118

Lift the contact spring (1) slightly
and remove the throttle cable (2).

Install in the reverse sequence.

Check that the throttle cable (1),
contact spring (2), protective
tube (3) and insulator (4) are
properly seated.

8.2.3

Throttle Cable

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды