Stihl FC 75 Скачать руководство пользователя

Страница: 14 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Remove the screw (arrow) from
the starter.

936RA000

Remove the screw (1) from the
fan housing.

Remove the shroud (2).

Install in the reverse sequence.

936RA001

Make sure the gaskets on either
side of the cylinder, and the
ignition lead (arrow), are located
in the guides in the shroud.

936RA304

Troubleshooting chart,

4.1.

Removing

– Remove the shroud,

5.1

Take out the screws (arrows).

– Remove the engine from the fan

housing and put it to one side.

936RA002

Inspect the clutch drum. There
should be no scores or signs of
excessive wear.

936RA003

If there are noticeable wear
marks on the inside diameter of
the clutch drum (1), check its wall
thickness. If it is less than about
80% of the original thickness, fit a
new clutch drum,

5.2.2

148RA101

80%

100%

Pull off the spark plug boot (1).

Unscrew the spark plug (2).

936RA004

1 2

Engine

5.1

Shroud

5.2

Clutch

5.2.1

Removing and Installing

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды