Stihl FC 75 Скачать руководство пользователя

Страница: 16 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Attach one end of each spring (1)
to the clutch shoes.

Use the hook (2) 5910 890 2800
to attach other ends of springs
and press them firmly into the
clutch shoes.

936RA291

Screw the clutch into position
(lower hexagon facing outwards)
and tighten it down firmly,

3.2

936RA006

Check that the plugs are in
position in the fan housing, fit
them if necessary.

936RA007

Position the engine against the
fan housing, making sure the
lugs (1) engage the plugs (2).

– Fit fan housing mounting screws

and tighten them down firmly,

3.2

936RA008

– Remove the locking strip from the

cylinder.

– Install the spark plug and tighten

it down firmly,

3.2

– Check if spark plug has a

detachable adapter nut. If so,
make sure it is properly fitted and
firmly tightened.

– Fit boot on the spark plug.

– Fit the shroud,

5.1

– Remove the engine,

5.2.1

– Remove the rubber element (AV

system) from the fan housing,

7.1

Use pliers (1) 0816 610 1495 to
remove the circlip from the clutch
drum’s output stub.

936RA111

Use drift (1) 4180 893 4400 to
press the clutch drum out of the
ball bearing.

936RA112

5.2.2

Clutch Drum

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Похожие инструкции для FC 75

Бренды по названию

Популярные бренды