Stihl FC 75 Скачать руководство пользователя страница 47

Страница: 47 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Use a new gasket (arrow).

– Mount the spacer flange and

tighten down the screws firmly,

3.2

Assemble all other parts in the
reverse sequence.

936RA363

– Remove the shroud,

5.1

– Carry out leakage test,

9.2.1

Take out the M3x12 screws (1).

Remove the end cover with
cap (2).

936RA223

Take out the M3x8 screws (1).

Remove the flange (2).

936RA224

Take the cap out of the end cover.

936RA258

Inspect the metering diaphragm
and gasket and replace if
necessary,

9.3.3

Install in the reverse sequence.

Additional holes in the gasket and
diaphragm (if there are any) must

936RA025

line up with those in the carburetor
and flange.

– Insert the M3x8 screws in the

flange mounting holes (without
integrally cast spacers) and
carburetor and tighten them
down.

Note:

STIHL recommends that the flange
mounting with an oval end cover be
converted to the later version with a
square end cover,

9.3.2

9.3

Servicing the Carburetor

9.3.1

Flange Mounting with Oval End Cover

Содержание FC 75







































































Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды

Stihl FC 75, Руководство по обслуживанию

Результаты поиска

Содержание FC 75

Отзывы:

Бренды по названию

Популярные бренды