STERO SD3 Series Скачать руководство пользователя страница 42

Страница: 42 / 71

CONTROLS

ILLUS.
PL-60512

PART NO.

NAME OF PART

AMT.

0P-428299

Switch - Membrane Keypad.......................................................................................................1

0P-428301

Trim - Keypad.............................................................................................................................1

0P-578212

Foam Tape..............................................................................................................................AR

0P-428217

Display Module...........................................................................................................................1

0A-108045

Clamp - Wire (3/4 I.D.)...............................................................................................................1

0P-678336

Lock Nut 3/16 Washer Type (SST)............................................................................................1

0A-108045

Clamp - Wire (3/4 I.D.)...............................................................................................................1

0P-678137

Nut 10-24 Hex (SST)..................................................................................................................1

0P-678335

Stop Nut 10-24 Hex Elastic (SST)..............................................................................................1

0P-428218

Standoff......................................................................................................................................2

0P-428306

Control Board Assy....................................................................................................................1

0P-458219

Ribbon Cable Assy.....................................................................................................................1

0P-678141

Stop Nut 6-32 Hex (SST)...........................................................................................................2

0P-428218

Standoff......................................................................................................................................2

0P-428220

Board - Relay Assy.....................................................................................................................1

0P-678141

Stop Nut 6-32 Hex (SST)...........................................................................................................2

0P-528313

Fuse (250 V.) (1 Amp.)...............................................................................................................1

0P-528315

Fuse (250 V., 0.1 Amp.).............................................................................................................1

0P-428185

Standoff - Reed Board (3/8) (Control Board)..............................................................................2

0P-428185

Standoff - Reed Board (3/8) (Relay Board)................................................................................2

0P-428300

Corner - Display.........................................................................................................................1

0P-678336

Lock Nut 3/16 Washer Type (SST)............................................................................................4

0A-108045

Clamp - Wire (3/4 I.D.)...............................................................................................................4

0P-698261

Plate (Patent Numbers)..............................................................................................................1

0A-698310

Label - Warning (Fuse) (Electric Heat) Label - Warning............................................................1

0A-698303

Plate - Machine Data..................................................................................................................1

0P-698207

Label - Warning (Electric Heat W/Booster) Label - Warning......................................................1

0A-698311

Label (Error Code)......................................................................................................................1

0P-698208

Label - Instruction.......................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 5 -

F-43302 Rev. B (October 2015)

Содержание SD3 Series








































































Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды

STERO SD3 Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды