STERO SD3 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 71

background image

TANK HEATER - TEST

Certain procedures in

this section require electrical test or
measurements while power is applied
to the machine. Exercise extreme
caution at all times and follow Arc Flash
procedures. If test points are not easily
accessible, disconnect power and
follow Lockout/Tagout procedures,
attach test equipment and reapply
power to test.

NOTE:

Tank must be filled with water (float switch

closed) in order to test tank heat circuit.

1.

Remove FRONT COVER.

2.

Open control door.

3.

Apply power to machine.

A.

Measure incoming voltage across line side
of the tank contactor 2CON and verify it
matches machine specifications on data
plate.

4.

Verify the following conditions are met.

A.

Tank is full of water.

B.

Float switch 1FS is closed.

C.

Wash tank thermistor 1QTM is good, not
open or shorted.

D.

There is a demand for heat (tank water
temperature is below set point).

5.

Turn machine on.

Shorting J8 terminals together without

having water in the tank may result in damaging the
tank heater.

A.

If temperature control circuit is not calling for
heat (relay board TANK HEAT LED not lit),
run machine through a cycle to activate tank
heater. Alternately, short the relay board
TANK HEAT (AM) -J8 pins together to
energize the tank heater.

Fig. 4

6.

While the TANK HEAT (AM) LED is on, verify that
the tank heat contactor 2CON is energized.

A.

If contactor is not energized, check for
120VAC across coil.

1)

If 120VAC is not present, check high
limit thermostat 1TAS.

B.

If contactor is energized, check:

1)

Voltage across all legs on load side of
contactor.

2)

Current flow through all elements of
heater.

RATED TANK HEATER ELEMENT CURRENTS

Voltage/Phase

Amperes

Power (Watts)

208/60/1

26A

5.4kW

240/60/1

30A

7.2kW

208/60/3

15A

5.4kW

240/60/3

17.3A

7.2kW

480/60/3

6A

5kW

7.

If the current reading on any of the elements is
not correct:

A.

Check the contacts of contactor 2CON.

B.

Check the wash tank heater element
resistance.

INDIVIDUAL TANK ELEMENT RESISTANCE

Voltage

Cold Resistance

208 - 240V

21.7 - 25.1Ω

480V

105 - 121.7Ω

SD3 Series - SERVICE PROCEDURES AND ADJUSTMENTS

F45576 (1015)

Page 10 of 37

«
...
8
9
10
11
12
...
»

Содержание SD3 Series








































































Отзывы:

Нет отзывов

Похожие инструкции для SD3 Series

Бренд: Hotpoint Страницы: 56

Бренд: Matsui Страницы: 8

Бренд: Indesit Страницы: 24

Бренд: Indesit Страницы: 16

Бренд: Ariston Страницы: 16

Бренд: SERVIS Страницы: 29

Бренд: Summit Страницы: 15

Бренд: montpellier Страницы: 24

Бренд: Baumatic Страницы: 36

Бренд: Samsung Страницы: 52

WW60J426 Series

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 60

Бренд: Samsung Страницы: 216

Бренд: Samsung Страницы: 64

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 248

Бренд: Samsung Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды