background image

MOTOR  AND PUMP

ILLUS.
PL-60515

PART NO.

NAME OF PART

AMT.

1

0P-678341

Cap Screw 5/16-18 x 1-1/8 Hex Hd. (SST)................................................................................2

2

0P-578248

Gasket - Adapter........................................................................................................................1

3

0A-108285

Adapter (Pump-to-Manifold).......................................................................................................1

4

0P-678169

Washer (SST).............................................................................................................................2

5

0P-678142

Stop Nut 5/16-18 Hex (SST)......................................................................................................2

6

0A-108239

Screen - Pump...........................................................................................................................1

7

0P-678165

Lockwasher 5/16 Helical (SST)..................................................................................................4

8

0P-678139

Nut 5/16-18 Hex (SST)...............................................................................................................4

9

0A-108211

Clamp - Hose.............................................................................................................................2

10

0P-688297

Hose - Pump Intake....................................................................................................................1

11

0P-678294

Mach. Screw 6mm x 18mm (SST)...........................................................................................11

12

0B-108293

Pump Shell (Outer).....................................................................................................................1

13

0B-108289

Impeller (60 Hz.).........................................................................................................................1

14

0P-578288

Shaft - Seal.................................................................................................................................1

15

0P-578292

Seal............................................................................................................................................1

16

0P-678295

Lock Nut 6mm (SST)................................................................................................................11

17

0A-108279

Bracket - Motor Mounting...........................................................................................................1

18

0P-418286

Motor (208-240/480/60/3)...........................................................................................................1

19

0P-418287

Motor (208-240/60/1)..................................................................................................................1

20

0P-418296

Fan - Cooling 60 Hz...................................................................................................................1

21

0C-418283

Pump & Motor Assembly 208-240/480/60/3...............................................................................1

22

0C-418284

Pump & Motor Assembly 208-240/60/1......................................................................................1

23

0A-108213

Clamp - Hose.............................................................................................................................2

24

0P-688225

Hose - Discharge........................................................................................................................1

25

0P-678290

Lockwasher 10mm (SST)...........................................................................................................1

26

0P-678291

Jam Nut 10mm (SST).................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 11 -

F-43302 Rev. B (October 2015)

Содержание SD3 Series








































































Отзывы: