STERO SD3 Series Скачать руководство пользователя страница 62

Страница: 62 / 71

LOW WATER PROTECTION AND ELECTRIC HEAT

ILLUS.
PL-60522

PART NO.

NAME OF PART

AMT.

0P-678333

Nut 3/8-16 (Brass) (Supplied With Heater).................................................................................1

0P-678350

Lockwasher 3/8 Helical (SST)....................................................................................................1

0B-108216

Plate - Electric Heat....................................................................................................................1

0P-578174

O-Ring........................................................................................................................................1

0P-558251

Element - Heater Wash Tank (6 kW) (200 V) Element - Heater (6.2 kW) (208 V.).................AR

0P-558249

Element - Heater (5 kW) (200-240 V., 50/60 Hz., 1 & 3 Ph.) Element - Heater (5 kW)
(200-240 V., 60 Hz., 1 & 3 Ph.)..................................................................................................1

0P-558250

Element - Heater (480 V.) Element - Heater (5 kW) (480 V., 60 Hz., 3 Ph.)..............................1

0P-678337

Retaining Ring............................................................................................................................1

0A-108184

Retainer - Float...........................................................................................................................1

0C-108278

Switch & Probe Assy. (4-Wire) (Short) (Incls. Items 9 & 11)......................................................1

0C-108192

Float Assy...................................................................................................................................1

0P-578175

O-Ring........................................................................................................................................1

0B-108190

Cap & Stud Assy........................................................................................................................1

0P-678354

Washer - Thrust..........................................................................................................................1

0P-678353

Lockwasher 1/2 External Shakeproof (SST)..............................................................................1

0P-678334

Jam Nut 1/2-20 Hex (SST).........................................................................................................1

0P-578173

O-Ring........................................................................................................................................1

0A-108191

Retainer - Cap............................................................................................................................1

0P-678164

Lockwasher 1/4 Helical (SST)....................................................................................................1

0P-678138

Nut 1/4-20 Hex (SST).................................................................................................................1

0P-658202

Control - Temperature................................................................................................................1

0A-108209

Bracket - High Limit....................................................................................................................1

0P-678335

Stop Nut 10-24 Hex Elastic (SST)..............................................................................................2

SD3 DISHWASHER REPLACEMENT PARTS

- 25 -

F-43302 Rev. B (October 2015)

Содержание SD3 Series








































































Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды

STERO SD3 Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание SD3 Series

Отзывы:

Похожие инструкции для SD3 Series

Бренды по названию

Популярные бренды